CUARENTAYCUATRO.ES ≡ Otros Idiomas Fruit & Vegetables Mold & Casing Tabletop
  • Discontinued Products

  • CIR.LV8729.BLK.O1 LV8729 Stepstick Style Stepper Driver (Discontinued)

CIR.LV8729.BLK.O1 LV8729 Stepstick Style Stepper Driver (Discontinued)

$11.92 $21.1
Product Description Want create site? Find Free WordPress Themes and plugins.LV8729 stepper motor driver module in the common StepStick style format This product has been replaced from 1 May 2021, please refer to the relevant product category here for alternatives This product page is here as a reference for customers who purchased this part prior to 1 May 2020 Plug in replacement for A4988 & DRV8825 on any board that accepts StepStick format drivers up to 1/128 microstepping quiet maximum 2.0A if adequately cooled according to supplier Quiet stepper motor Drivers LV8729 Input voltage: 6-36V Max current: 1.5A (Module supplier says 2A but they copy / pasted a bunch of other incorrect information so I don’t trust them) Micro Stepping: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128 Heat sink included so USE IT LV8729V-Datasheet Module pins: Make sure you orient it correctly in your controller board or you may kill it Microstep settings: Micro stepping jumpers M1 M2 M3 1 full step 0 0 0 1/2 step 1 0 0 1/4 step 0 1 0 1/8 step 1 1 0 1/16 step 0 0 1 1/32 step 1 0 1 1/64 step 0 1 1 1/128 step 1 1 1 Current settings The output motor current is set according to VREF.  VRef is measured Viewed from the top Rotate the potentiometer clockwise to decrease vRef & anticlockwise to increase vRef Be gentle, it is a small surface mounted potentiometer attached to the underside of the PCB substrate so be nice to it. Use the right size small slotted screwdriver, if you do so, no downward force is necessary, otherwise you may separate the potentiometer from the module Precautions: Adjust without the motors connected to avoid potential damage to your motors (once you have your desired settings then connect your motors) If your motors run hot afterwards, recheck your calculations, dial it back.. The sense resistors on these modules are R220 = 0.22 ohms so the formula for setting vRef per the datasheet is: I = (VREF / 5) / 0.22 so: VREF = I * 1.1 Example: if your desired current is 1.2A: VRef = 1.2 * 1.1 = 1.32V My handy tables: Heat sink orientation   Did you find apk for android? You can find new Free Android Games and apps.
Discontinued Products

Discontinued Products

  • CIR.LV8729.BLK.O1 LV8729 Stepstick Style Stepper Driver (Discontinued)
    $11.92 $21.1
  • 17HS4401.S5F.O1 stepper motor, 5mm shaft (discontinued)
    $14.36 $24.4
  • 17HS4401.S5F.O2 stepper motor, 5mm shaft (discontinued)
    $14.36 $25.55
  • 17HS4401.S5F.O3 stepper motor, 5mm shaft (discontinued)
    $14.36 $19.67
  • 17HS3401.S5F.O1 stepper motor, 5mm shaft (discontinued)
    $12.56 $16.07

© 2026 - CUARENTAYCUATRO.ES